ASE Practice Test #5 2 — Questions and Answers
Question 1: A technician performs a relative cylinder compression test (cylinder contribution test) and finds cylinder 4 has the lowest contribution. What is the NEXT step to determine the root cause?
- Replace the spark plug and ignition coil on cylinder 4 immediately
- Perform a conventional compression test followed by a cylinder leakdown test on cylinder 4 to differentiate between compression loss (rings, valves) and ignition/fuel issues (Correct answer)
- Replace the head gasket on cylinder 4 bank
- Check the fuel injector balance rate on cylinder 4 only
Correct answer: Perform a conventional compression test followed by a cylinder leakdown test on cylinder 4 to differentiate between compression loss (rings, valves) and ignition/fuel issues
The relative compression test identifies WHICH cylinder is weak, not WHY it is weak. The follow-up is a compression gauge test to quantify the actual cylinder pressure, and if low, a cylinder leakdown test to determine where the compression is leaking (past rings — heard at oil filler; past exhaust valve — heard at exhaust; past intake valve — heard at intake; past head gasket — seen as coolant bubbling). This systematic approach identifies the specific mechanical fault before disassembly.
Question 2: What does a KOEO (Key On Engine Off) test reveal that a KOER (Key On Engine Running) test does not?
- KOEO tests show only running faults; KOER shows stored faults
- KOEO tests check electrical circuit integrity and hard faults stored in memory without the influence of running engine conditions; KOER tests additional sensor and actuator performance under operating conditions (Correct answer)
- There is no difference between KOEO and KOER tests
- KOEO tests require a dynamometer; KOER tests do not
Correct answer: KOEO tests check electrical circuit integrity and hard faults stored in memory without the influence of running engine conditions; KOER tests additional sensor and actuator performance under operating conditions
KOEO (Key On Engine Off) self-tests check the electrical circuits connected to sensors and actuators — looking for opens, shorts, and out-of-range static values. Since the engine isn't running, transient faults from operating conditions don't interfere. Hard faults that exist at all times show up clearly. KOER (Key On Engine Running) tests check sensor and actuator performance under actual operating conditions, including dynamic sensor responses and system interactions. Both tests are part of complete OBD-I and some OBD-II manufacturer-specific diagnostic procedures.
Question 3: A technician measures a thermistor (NTC type) sensor resistance. As the temperature increases, what happens to the resistance reading?
- Resistance increases as temperature increases
- Resistance decreases as temperature increases — NTC stands for Negative Temperature Coefficient (Correct answer)
- Resistance stays constant regardless of temperature
- Resistance alternates between high and low as temperature rises
Correct answer: Resistance decreases as temperature increases — NTC stands for Negative Temperature Coefficient
NTC (Negative Temperature Coefficient) thermistors are used for coolant temperature sensors (CTS/ECT), intake air temperature sensors (IAT), and transmission temperature sensors. As temperature rises, electrical resistance through the NTC thermistor decreases. The ECM reads the resulting voltage drop across the sensor (in a voltage divider circuit) and converts it to temperature using a lookup table. A failed sensor stuck at high resistance causes the ECM to see a false cold signal, causing rich running and no cooling fan activation.
Question 4: What is the function of variable displacement (cylinder deactivation) technology in a V6 or V8 engine?
- To automatically switch from gasoline to diesel fuel during highway driving
- To deactivate specific cylinders (closing their valves and stopping fuel injection) during light load conditions, reducing the effective engine displacement and significantly improving fuel economy (Correct answer)
- To increase displacement during heavy acceleration by adding additional displacement through variable compression pistons
- To rotate which cylinders fire each revolution for even wear
Correct answer: To deactivate specific cylinders (closing their valves and stopping fuel injection) during light load conditions, reducing the effective engine displacement and significantly improving fuel economy
Cylinder deactivation (Active Fuel Management/GM, MDS/Chrysler, VTEC/Honda) shuts down half of the engine's cylinders during light load conditions (highway cruise, gentle acceleration). The system closes the intake and exhaust valves on deactivated cylinders and cuts fuel injection to them. The remaining active cylinders work harder to maintain vehicle speed, operating at a more efficient throttle position with less pumping loss. The transition is controlled by solenoids actuating special lifters that collapse, preventing valve actuation.
Question 5: A technician uses a scan tool and finds the O2 sensor upstream (pre-catalyst) is switching normally, but the downstream O2 sensor reads a steady 0.1V. What does a steady low voltage downstream O2 sensor indicate?
- The catalyst is functioning correctly
- Permanently lean downstream exhaust — possible causes include an exhaust leak between the upstream sensor and converter, or a failed catalyst that is not processing the exhaust gases at all (letting lean exhaust pass through) (Correct answer)
- The downstream O2 sensor is shorted to ground
- The ECM is commanding open-loop operation
Correct answer: Permanently lean downstream exhaust — possible causes include an exhaust leak between the upstream sensor and converter, or a failed catalyst that is not processing the exhaust gases at all (letting lean exhaust pass through)
A downstream O2 sensor that reads a steady low voltage (approximately 0.1V, indicating lean) suggests very lean exhaust consistently reaching the downstream sensor. Possibilities include: a major exhaust leak between the upstream sensor and the converter (diluting with fresh air), a severely failed catalyst that has no conversion activity (allowing raw lean exhaust through), or a failed downstream O2 sensor stuck at a low value. Comparing with a vacuum leak diagnosis and exhaust inspection helps differentiate these causes.
Question 6: A vehicle's traction control system activates unexpectedly on dry pavement with no wheel slip occurring. Which component failure is MOST likely causing false traction control activation?
- Failing brake master cylinder
- A wheel speed sensor producing an erratic or intermittent signal — the ABS/traction control module interprets the false speed reading as wheel slip and activates traction control unnecessarily (Correct answer)
- Low engine oil level
- Faulty throttle position sensor
Correct answer: A wheel speed sensor producing an erratic or intermittent signal — the ABS/traction control module interprets the false speed reading as wheel slip and activates traction control unnecessarily
Traction control systems monitor wheel speed sensors to detect wheel spin (one or more wheels spinning faster than others). If a wheel speed sensor produces erratic signals due to a failing sensor, damaged wiring, or a rusted/damaged tone ring, the module may see a false speed differential that it interprets as wheel spin — activating traction control and reducing engine power on dry pavement where no actual slip exists. Diagnosing which wheel speed sensor is producing erratic live data with a scan tool identifies the faulty sensor.
ASE Practice Test #5 2
A technician performs a relative cylinder compression test (cylinder contribution test) and finds cylinder 4 has the lowest contribution.
What is the NEXT step to determine the root cause?
What Practice Test Geeks adds beyond an AI chat for ASE
An AI chatbot can quiz you, but it can't reproduce the exam conditions or keep your record. Here you get:
- A timed, full-length ASE mock exam — 40 questions in 120 minutes with a 70% pass mark, modeled on the official exam's question count and time limit, followed by a score report broken down by exam domain.
- A fixed ASE question bank: the same test every attempt, so your score is comparable from one try to the next instead of changing with every regenerated quiz.
- Progress saved on your device: completed tests, scores and missed questions stay in My Progress, so you can retake only what you got wrong.
- A printable ASE cheat sheet you can print or save as a PDF.
- ASE flashcards built from the same question bank.